DSC PC1404 v1.1 Manuale Utente

PC1404 v1.1User ManualIMPORTANT: This manual contains information on limitations regarding product useand function and information on the limitations

7Disarming from an LCD Alphanumeric Keypad: Disarming from an LCD Fixed Message/Icon Keypad Enter your access code to disarm anytime the system is arm

8When An Alarm SoundsFire AlarmIf your system has been installed with fire detectors and the alarm sounds in a pulsing mode, followyour emergency evac

9If the Master Code has been programmed as user changeable, to program the Master Code, enter[][5][current Master Code][40][new Master Code]. Press [

10PC1555RKZ:Press the [F] key for two seconds to send a FIRE transmission.Press the [A] key for two seconds to send an AUXILIARY transmission.Press th

11Access Code ProgrammingIn addition to the Master Access Code, you can program up to 39 additional User Access codes.Press , plus your Master Access

12Programming CodesProgramming codes from an LCD Keypad:Master CodeBe sure to record your new Master Code on the “System Information” page in this boo

13To erase a code: Enter [][5][Master Code] [code number 01 to 39][]. Press [#] to return to the Ready state. Be sure to record your new codes on t

14Bypass GroupsA bypass group is a selection of zones programmed into the system. If you bypass a group of zoneson a regular basis, you can program th

15Setting the System Date and TimeTo set the system time, enter [][6] followed by the Master Code. Press [1]. The keypad will nowaccept 10 consecutiv

16NOTE: If you suspect that a fire alarm has been transmitted and that there is no fire condition, call the monitoring station to avoid an unnecessary

iTable of ContentsAbout Your Security System ... 1Carbon Monoxide Detection (must be enabled by your Insta

17Changing Brightness/ContrastPK5500 keypadsWhen this option is selected, the keypad will allow you to scroll through 4 different brightness/con-trast

18System InformationFill out the following information for future reference and store this manual in a safe place.Access CodesYour Master Code is: ___

19Zone InformationThere are ________ active zones on the system.Zone Protected Area Zone Type12345678[F] FIRE[A] AUXIL-IARY[P] PANICThe Exit Delay Tim

20Testing Your SystemAlarm TestThe Alarm Test provides a two-second test of the keypad sounder and bell or siren. The keypad lightsand communicator ar

21Guidelines for Locating Smoke Detectors and CO DetectorsThe following information is for general guidance only and it is recommended that local fire

22Carbon Monoxide DetectorsCarbon monoxide is colorless, odorless, tasteless, and very toxic. Italso moves freely in the air. CO detectors can measure

23FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved byDigital Security Controls could void your authority to use thiseq

IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Componentsis copyrighted and is purchased under the following license

© 2013 Tyco International Ltd. and its Respective Companies. All Rights Reserved. Toronto, Canada • www.dsc.com • Printed in Canada The trademarks, lo

iiImportant Safety Instructions for UserCAUTION: When using equipment connected to the TELEPHONE NETWORK, there are basic safety instructions that sho

1About Your Security SystemYour DSC Security System has been designed to provide you with the greatest possible flexibility andconvenience. Read this

2System KeypadsPC1555RKZLCD5511DisplaySystem LightsNumber PadLED55111 2 3 4 5 6 7 8 0 * # 9 StayAwayChimeResetQuickExitPK5500/PK5501StatusLightsZoneL

3Keypad Display Symbols1 Clock Digits 1, 2 – These two digits indicate the hour digits when the local clock is active, andidentify the zone when the O

4IMPORTANT NOTICEA security system cannot prevent emergencies. It is only intended to alert you and – if included –your central station of an emergenc

5NOTE: If you arm the system with a zone bypassed or with a trouble present, your security protection is reduced. Arming from an LCD Fixed Message/Ico

6Night ArmingTo fully arm the system when it has been armed in Stay Mode, press [][1] at any keypad, or pressthe night arming function key if it has