DSC PC1500 - REV8 Manuale delle Istruzioni Scaricare il pdf (Pagina 11)

ENTRY DELAY OFF ARMING

If you wish to arm your system and eliminate the entry delay, enter [

∗

][9]

before your access code. The “Armed” light will flash as a reminder that the

system is armed and has no entry delay. An entry through any zone

programmed as a delay zone will create an instant alarm.

e.g. To arm without entry delay, press [

∗

][9][access code]

DISARMING THE SYSTEM

Enter the premises only through the door(s) designated by your installer as the

entry door. Entering by any other door will sound an immediate alarm. As soon

as the entry door is opened, the keypad sounder will come on to indicate that

the system should be disarmed. Go to the keypad and enter your four digit

access code. If an error is made entering the code, press the [#] key and enter

your code again. As soon as the correct code is entered, the “Armed” light will

go out and the keypad sounder will silence.

The correct access code must be entered before the entry time expires. The

entry time delay may be changed by your installer. If an alarm occurred during

the period the system was armed, the “Memory” light and the zone light of the

zone that caused the alarm will flash for two minutes. After the two minute

period, the “Memory” light and zone light will stop flashing and the panel will

return to the ready state. Pressing the [#] key during the two minute period will

cancel the alarm memory display.

If a trouble is present when the panel is disarmed, the “Trouble” light will come

ON (See Viewing Trouble Conditions section to determine the source of the

trouble.) Note that troubles will not display while the system is in the Alarm

Memory Display Mode.

If you return home and find that an alarm has occurred while you were away, it

is possible that an intruder may still be on the premises. Go to a neighbour's

house and call the local police to investigate.

QUICK ARM FEATURE

When the Quick-Arm feature is enabled, the system may be armed simply by

pressing [

∗

][0] instead of the 4 digit access code. This feature allows a person

to arm but not disarm the system.

Enter [

∗

][6][Master Code][4] to turn the Quick-Arm feature ON and OFF. When

the command is entered, the keypad buzzer will beep 3 times if Quick-Arm is

being enabled and will sound one long beep if it is being disabled.

Press

[#]

to return to Ready.

DOOR CHIME FEATURE

The door chime feature is used, while the panel is disarmed, to provide a tone

from the keypad each time a door or window is opened or closed. The doors

and windows which will provide this indication are programmed by your installer.

Enter [

∗

][6][Master Code][6] to turn the door chime feature ON and OFF. When

the command is entered, the keypad buzzer will beep 3 times if the door chime

feature is being enabled, and will sound one long beep if it is being disabled.

Press

[#]

to return to Ready.

ZONE BYPASSING

(Continued)

For security reasons, your installer may prevent the bypass command from

working on certain zones. The “Bypass” light is ON as long as ONE or more

zones are bypassed. Do not unintentionally arm the system with zones

bypassed.

Zone bypasses are automatically cancelled each time the system is disarmed

and must be re-applied before the next arming.

VIEWING TROUBLE CONDITIONS

The PC1500/PC1550 continuously monitors a number of possible trouble

conditions. If one of these trouble conditions occur, the keypad will beep twice

every 10 seconds and the keypad “Trouble” indicator will light. Pressing any key

on the keypad will silence the sounder but the “Trouble” light will remain ON until

the trouble condition is cleared. If you cannot determine the cause of the trouble

condition, contact your installer for assistance.

To View Type of Trouble:

Press [

∗

][2] to display the type of trouble. A zone light will come on to indicate

which type of trouble exists.

Press

[#]

to return to Ready.

LIGHT TYPE OF TROUBLE

1 ...........Low or disconnected standby battery.

2 ...........Loss of AC power (Loss of AC power will turn on the

trouble light but keypad sounder will not sound).

3 ...........Fuse open (bell/siren).

4 ...........Failure to communicate with monitoring station.

5 ...........Tamper trouble.

6 ...........Loss of time on the system clock.

KEYPAD ZONES

There are three keys on the keypad labelled [F] Fire, [A] Auxiliary and [P] Panic.

These keys are only functional if they have been programmed by your installer.

The installer should indicate which of these keys are functional by placing a

coloured label next to the key symbol on the keypad door label.

[F] Fire

Holding this key down for two seconds will sound a Fire Alarm. The alarm will

sound pulsing. The keypad will sound three beeps once the panel has accepted

the alarm. An auxiliary warning device is also activated if your installer has

connected it to your system. To silence the alarm, enter a valid access code.

[A] Auxiliary

Holding this key down for two seconds activates this function if your installer has

programmed it. There is no audible alarm and no lights on the keypad will come

on. When the panel has accepted the alarm, the keypad will sound a series of

beeps. An auxiliary warning device is activated ONLY IF connected to your

system by your installer.

4 9

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Commenti su questo manuale

Nessun commento

DSC PC1500 - REV8 Manuale delle Istruzioni Pagina 11

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso DSC PC1500 - REV8