DSC PC1500 - REV8 Manuale delle Istruzioni Scaricare il pdf (Pagina 12)

MASTER CODE

The 4 digit Master Code is used to arm and disarm the security system, to

program additional security codes and to change other system features. The

Master Code will be supplied to you by your installer. All keypad entries are

made by pressing one key at a time. (See Additional Codes section)

ARMING THE SYSTEM

Check the following items before arming the system:

Bypass light

If the “Bypass” light is ON, insure that zones are intentionally bypassed before

arming the system (See Zone Bypassing section).

Trouble light

If the “ Trouble” light is ON, check to see what the trouble condition is and call

for service. (See Viewing Trouble Conditions section).

Ready light

If the “Ready” light is NOT ON, check to see that all doors and windows are

closed and that motion is stopped in areas covered by motion detectors. The

system cannot be armed unless the “Ready” light is ON indicating that all

zones are closed.

NOTE:

The system may be armed with a zone bypassed or a trouble present

but your security protection will be reduced.

To Arm

Enter your 4 digit access code. As each digit is entered, the keypad sounder will

beep. If the correct access code is entered, the keypad sounder will beep

quickly and the “Armed” light will come ON.

If the access code was entered incorrectly or the “Ready” light comes ON, the

keypad buzzer will sound steadily for 2 seconds. If this occurs, press the [#] key

and re-enter your access code.

When the correct access code is entered and the “Armed” light comes ON, exit

the premises through the door indicated by your installer as the Exit-Entry door.

At the end of the exit delay period, all lights, except the “Armed” light, will go out

and the system will be armed. The exit time delay can be changed by your

installer.

AUTO-BYPASS OPTION - HOME-AWAY ARMING

This feature, if selected by your installer, will allow you to arm your system with any

valid access code and the system will automatically bypass the interior zones. The

“Bypass” light will come on. If you exit within the allowed exit time, the system will

automatically activate the interior zones and the “Bypass” light will go out. This

feature is designed to save the customer from having to manually bypass interior

zones each time they wish to arm the system and remain at home.

In residential applications where the system has been armed and the interior

zones are automatically bypassed, the interior zones can be reactivated from a

keypad that is outside the interior zone's protection area. To reactivate the interior

zones, press [

∗

] then [1] and the “Bypass” light will go out.

[P] Panic

Holding this key down for two seconds causes a steady tone on your siren or

bell if your installer has programmed this key for audible operation. An auxiliary

warning device is also activated if your installer has connected it to your

system. Enter a valid access code to silence the alarm.

FIRE ALARM OPERATIONS

Alarm

On a fire alarm, the bell/siren will sound pulsing. The digital communicator

transmission is delayed for 30 seconds. If the alarm is not acknowledged

within the 30 second delay, the communicator will transmit the fire alarm to the

monitoring station.

Silence

To silence the bell/siren, press the [#] key. If the alarm is silenced and the

smoke detector is not reset, the alarm will resound after 90 seconds.

Reset

To restore the smoke detector(s) to normal, press [

∗

][7]. If the detector still

has smoke in it, the alarm will resound and the sequence described above will

repeat. If the detector is clear of smoke, the system will return to normal.

NOTE:

If you suspect that the communicator has transmitted and there is

no fire condition, call the monitoring station to avoid an

unnecessary response. If a fire condition is apparent, follow your

evacuation plan immediately. If the alarm sounds at night,

evacuate immediately.

TESTING YOUR SYSTEM

It is recommended that you test your system weekly. Perform system

tests in the off-peak hours, such as early morning or late evening.

1. Inform the monitoring station that you are testing your system.

2. Disarm the system (“Ready” light ON).

3. Perform a bell/battery test by pressing [

∗

][6][Master Code]. The signal will

sound for about 2 seconds. If a trouble occurs after the test, press [

∗

][2] to

view the trouble condition.

4. Activate each sensor in turn (e.g. open a door/window or walk in motion

detector areas). Observe the zone light come ON when the zone is

activated. The zone light will go OFF when the system restores to normal

(i.e. door or window closed).

5. If they are programmed for operation, press the [F], [A], and [P] keys in

turn. The [F] key will sound the bell/siren in a pulsed mode. Enter the access

code to silence the alarm. The [A] key is silent. The [P] key may be

programmed as silent or audible. If the alarm sounds, enter the access

code to silence.

6. If the panel has a zone programmed for fire, activation will cause the alarm

signal to sound in a pulsed mode. CAUTION:

Do not use an open flame

or burn materials to test a smoke detector.

Contact your alarm installer

for information on safe methods to activate a smoke detector.

7. Should the system fail to operate properly, call your alarm dealer for service.

310

1 2 ... 7 8 9 10 11 12 13 14 15 16

Commenti su questo manuale

Nessun commento

DSC PC1500 - REV8 Manuale delle Istruzioni Pagina 12

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso DSC PC1500 - REV8