Installation ManualPC5010 CP-01IMPORTANTThis manual contains information on limitations regarding product use and function and information on the limi
4BackplatesThere are two different backplates available for keypadsto mount an audio station next to a keypad:PC55BP1 BackplateUse this backplate when
5Section 2: Installation and WiringThe following sections provide a complete description of how to wire and configure devices and zones.2.1 Installati
6Keybus Terminals - RED, BLK, YEL, GRNThe Keybus is used by the panel to communicate withmodules and by modules to communicate with the panel.Each mod
Installation and Wiring: 2.6 Assigning Zones to Zone Expanders7PC5010 CP-01 Device Ratings (@ 12 VDC)• LCD5500Z/LCD5520Z Keypad: 85 mA• LCD5501Z Keypa
8How to Program Function KeysEach of the 5 function keys on each keypad may be pro-grammed for different operation.1. Enter Installer Programming. 2.
Installation and Wiring: 2.10 Zone Wiring9End of Line Resistors . . . . . . . . . . . . . . . . Section [013], Option [1]Single End of Line Resistors
10LINKS 2X50/LINKS 3000/Skyroute™Refer to the LINKSX50, LINKS3000 and Skyroute™Installation Manuals for wiring and installation details.2.11 Keypad Zo
11Section 3: How to ProgramThe following section of the manual describes how toenter Installer Programming and how to program the var-ious sections.NO
123.5 Viewing ProgrammingLED and LCD5501Z KeypadsAny programming section can be viewed from an LED orLCD5501Z keypad. When a programming section isent
13Section 4: Keypad CommandsUse any system keypad to enter commands, or to program the PC5010 CP-01 security system. The LED keypad uses functionand z
14The keypad will display the event number, partition, timeand date of the event in question. Use the [*] key to togglebetween this information and th
Keypad Commands: 4.2 [*] Commands15[*] [3] Alarm MemoryThe memory light will be on if any alarm occurred duringthe last armed period or if an alarm oc
16Installer Programming - Codes and OptionsThere are three codes which can be programmed by theinstaller in Installer Programming: the Master CodeMast
Keypad Commands: 4.3 Function Keys17[*] [0] Quick ArmIf the Quick Arm EnableQuick Arm EnableQuick Arm EnableQuick Arm Enable option is enabled the pan
18[15] - General Voice Prompt HelpThis feature can only be programmed if both theEscort5580(TC) and the PC5936 audio matrix module arebeing used. When
19Section 5: Programming SectionsThe structure of this section corresponds with the structure of the Programming Worksheets (PWS) and is intended to b
205.1 For the Record PWS Sect 1This Section identifies the client, installation date, Installer Code, hardware configuration and programming summary f
Programming Sections: 5.3 Basic Programming PWS Sect 321[005] - System TimesThis section has 3 sub-sections, 1 for each of the 2 parti-tions, and 1 fo
22[006]-[008] Special Access Codes These sections require 4 or 6 digits to be entered. [006] - Installer Code Installer Lockout Enable . . . . . . .
Programming Sections: 5.3 Basic Programming PWS Sect 32310 Latched System Event (Strobe) This output will activate when any of the selected system eve
iiNew FeaturesPC5200 SupportThe PC5010 CP-01 v3.1 and higher supports the new PC5200 Power Supply module. See PC5200 Power Supply Output Module, Pg 2.
24[012] - Keypad Lockout OptionsThe panel can be programmed to ‘lockout’ keypads if aseries of incorrect access code entries is made. After theNumber
Programming Sections: 5.3 Basic Programming PWS Sect 325Option Definition On/Off Description2 Bell During Auto-armON Bell Squawk During Auto-arm Enabl
26Option Definition On/Off Description7 Telephone Line Monitor ON Telephone Line Monitor enabled. The TLM function will be active and the system will
Programming Sections: 5.3 Basic Programming PWS Sect 327Option Definition On/Off Description3 Audible RF Jam Trouble BeepsON Audible RF Jam Trouble Be
28Option Definition On/Off Description2 Verbal Door Chime ON Verbal Door Chime Is Enabled. The system will verbally annunciate the zone (or programmed
Programming Sections: 5.4 Advanced Programming PWS Sect 429[020] - Keypad Zone Assignment Assigning Keypad ZonesEach keypad has a zone input to which
30times. If the Auto-arm is postponed, arming or disarmingthe panel will not affect the postpone sequence. [176] - Cross Zone/Police Code TimerThis op
Programming Sections: 5.6 Communicator Programming PWS Sect631Some of the Programmable Output options are also select-able by partition see Section 5
32disarmed and report to the central station. All other zonetypes will only go into alarm if the panel is armed.Reporting codes can be one or two digi
Programming Sections: 5.6 Communicator Programming PWS Sect633[342]-[343] - Opening (Disarming) Reporting Codes Access Codes 1-32The panel will trans
iiiPC5010 CP-01 Installer Programming Quick Reference Chart SIA False Alarm ReductionMinimum requirement system for SIA-FAR Installations :• 1 PC5010
34Installer Lead In:Installer Lead In:Installer Lead In:Installer Lead In: a reporting code will be sent to the cen-tral monitoring station when Insta
Programming Sections: 5.6 Communicator Programming PWS Sect635Pager FormatThe Communicator Format Communicator Format Communicator Format Communicator
36• SIA - This format uses 300 Baud FSK as the communi-cation medium. The account code can be 4 or 6 hexa-decimal digits in length, all reporting code
Programming Sections: 5.6 Communicator Programming PWS Sect637[378] - Test Transmission Time of DayProgram the time of the test transmission in this s
38OFF LINKS is backup of Land Line(s). The control panel will dial through the LINKS if the panel is having difficulty communicating over the phone li
Programming Sections: 5.6 Communicator Programming PWS Sect639 [390]-[393] LINKS PreamblesDownloading can be performed through the LINKS1000cellular
40(Downloading Telephone Number) . . . . . . . . . . . . . . .Section [490]Communicator Call Direction Options. . . . . . Section [351] to [376]Call L
Programming Sections: 5.8 Programmable Output Programming PWS Sect 841NOTE: To perform downloading via the T-Link module,Option [1], Section 401 must
42[551]-[564] PGM Partition AssignmentThe PC5010 CP-01 has an 8-bit toggle field per output thatdetermines which partitions the output is assigned to
Programming Sections: 5.9 International Programming PWS Sect 943 [701] FIRST INTERNATIONAL OPTION CODESOption International Code On/Off Description1
ivTable of ContentsSection 1: Introduction 11.1 About the PC5010 CP-01 System ... 11.2 About the PC5010 CP-01 Manual S
44[703] - Delay Between Dialing AttemptsFor standard (force) dialing, the panel will go off-hook,search for dial tone for 5 seconds, hang-up for 20 se
Programming Sections: 5.11 Special Installer Instructions PWS Sect 1145[903] - Module Supervision FieldWhen this mode is entered, the system will disp
46[995][Installer Code] - Restore Escort5580(TC) Factory Default ProgrammingWhen this section is successfully entered, all program-ming for the Escort
47Section 6: Listing Requirements6.1 UL Listed Commercial and Residential InstallationsThe installation requirements listed below mustbe met for the f
48Appendix A: Reporting CodesThe following tables contain Contact ID and AutomaticSIA format reporting codes. For more information onreporting code fo
49Section # Reporting Code Code Sent When...Dialer Direction*Automatic Contact ID CodesSIA Auto Reporting Codes**[344] Special Opening Opening (disarm
50Table2: Contact ID Zone Alarm/Restoral Event Codes (as per ADEMCO):Program any of these codes for zone alarms/restorals when usingthe standard (non-
FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use th
WARNING Please Read CarefullyNote to InstallersThis warning contains vital information. As the only individual in contact with system users, it is you
NOTES
vPC5010 CP-01 Wiring DiagramNOTE: Remove CON1 when using PGM2for 2-wire smoke
PC5010 CP-01 Module CompatibilityModule Compatible? CommentsClassic Escort (VPM-1) NoDLM-1 NoDLM-4 v1.x NoDLM-4 v1.0L YesDLM-7 NoEscort5580 v3.0 Yes
1Section 1: Introduction1.1 About the PC5010 CP-01 SystemThe PC5010 CP-01 is a high end security system. It sup-ports up to 32 zones, 2 separate parti
2Digital Communicator Specifications:• Supports all major formats including SIA, Contact ID,and Residential Dial• Split reporting of selected transmis
Introduction: 1.4 Additional Devices3PC5936 Audio Interface ModuleThe PC5936 audio interface module provides paging,intercom, baby listen-in and door
Commenti su questo manuale